Shore hardness
|HasUserLanguage=eng |HasAuthor=Quisadmi |HasTermDate=2015/4/16 |HasSourceLanguage=eng |HasTranslationsLanguage=deu |TranslationINnld= |SynonymINnld= |TranslationINnnl= |SynonymINnnl= |TranslationINbnl= |SynonymINbnl= |TranslationINces= |SynonymINces= |TranslationINdeu=Shore-Härte |TranslationINdde= |SynonymINdde= |TranslationINade= |SynonymINade= |TranslationINbde= |SynonymINbde= |TranslationINcde= |SynonymINcde= |TranslationINlde= |SynonymINlde= |TranslationINeng= |SynonymINeng= |TranslationINbri= |SynonymINbri= |TranslationIName= |SynonymIName= |TranslationINaus= |SynonymINaus= |TranslationINcae= |SynonymINcae= |TranslationINnze= |SynonymINnze= |TranslationINrus= |SynonymINrus= |TranslationINfra= |SynonymINfra= |TranslationINffr= |SynonymINffr= |TranslationINbfr= |SynonymINbfr= |TranslationINcaf= |SynonymINcaf= |TranslationINcfr= |SynonymINcfr= |TranslationINlfr= |SynonymINlfr= |TranslationINint= |SynonymINint= |TranslationINita= |SynonymINita= |TranslationINpol= |SynonymINpol= |TranslationINslk= |SynonymINslk= |TranslationINspa= |SynonymINspa= |TranslationINspc= |SynonymINspc= |TranslationINesc= |SynonymINesc= |TranslationINesg= |SynonymINesg= |TranslationINeus= |SynonymINeus= |TranslationINsve= |SynonymINsve= |TranslationINssv= |SynonymINssv= |TranslationINfsv= |SynonymINfsv= |HasComment=== Definitions ==
- The measuring of Shore hardness according to DIN ISO 7619-1 is the most applied measurement of the elastomer hardness. The Shore hardness gives the resistance of a rubber part towards the penetration of a cone-shaped pin with determined dimensions under a defined pressure. Shore A for softer compounds and Shore D for harder compounds is determined by the type of measuring pin.
To receive a perfect measuring result of the Shore hardness the test specimen must have a thickness of 6 mm. In many cases the measurement on finished parts with a small rubber wall thickness leads to wrong results.
Standard elastomer compounds for technical rubber moulded parts are lying in a range from 20 to 90 Shore A.
Besides the Shore hardness test with a cone shaped gauging tip there exists the IRHD test according DIN ISO 48 with a ball shaped gauging tip.
|TermStatus=Supervisor
}}- eng -
Contents |
Translations
| Language | Link |
|---|---|
| deu | Shore-Härte |
Definitions
- The measuring of Shore hardness according to DIN ISO 7619-1 is the most applied measurement of the elastomer hardness. The Shore hardness gives the resistance of a rubber part towards the penetration of a cone-shaped pin with determined dimensions under a defined pressure. Shore A for softer compounds and Shore D for harder compounds is determined by the type of measuring pin.
To receive a perfect measuring result of the Shore hardness the test specimen must have a thickness of 6 mm. In many cases the measurement on finished parts with a small rubber wall thickness leads to wrong results.
Standard elastomer compounds for technical rubber moulded parts are lying in a range from 20 to 90 Shore A.
Besides the Shore hardness test with a cone shaped gauging tip there exists the IRHD test according DIN ISO 48 with a ball shaped gauging tip.
